Basic Workshop Practice TestITI Electrician Test / By Er. Roshan Tajne / May 17, 2023 0% Created by Er. Roshan TajneElectrician 1st Year Basic Workshop Practice Test 1 / 15 Category: Basic Workshop Practice1) Which type of calliper is used to draw parallel lines along the outer edges of the materials ? | किस प्रकार के कैलीपर का प्रयोग पदार्थ के बाहरी सिरों पर समान्तर रेखाएं खींचने में होता है? A) Outside calliper | बाह्य कैलीपर B) Inside calliper | आतंरिक कैलीपर C) Spring joint calliper स्प्रिंग जोड कैलीपर D) Jenny calliper | जेनी कैलीपर 2 / 15 Category: Basic Workshop Practice2) Which type of stake is used for riveting or seaming tapered cone shaped articles ? किस प्रकार की स्टेक का उपयोग टेपिंग शंक के आकार के लेखों को रिवेटिंग या सीमिंग करने के लिए किया जाता है? A) Square stake | वर्गाकार स्टेक B) Hatchet stake | हैचेट स्टेक C) Blow horn stake | ब्लो हॉर्न स्टेक D) Bevel edged square stake | बेवल एज वर्गाकार स्टेक 3 / 15 Category: Basic Workshop Practice3) What is the use of mortise chisel ? | मोर्टाइज़ छेनी का क्या उपयोग है? A) Paring and finishing joints in wood | लकड़ी को छीलना एवं फिनिश देना B) Light chiselling cleaning sharp corners and in wood | लकड़ी में हल्का छेनीकरण तथा तेज़ किनारों की सफाई C) General chiselling work in wood | लकड़ी में | सामान्य छेनीकरण करना D) Making rectangular holes in wood | लकड़ी में आयताकार छेद करना 4 / 15 Category: Basic Workshop Practice4) Which type of half lap joint is used if one part of a job meets another part at some distance from the ends? | किस प्रकार का अर्ध लैप जोड़ प्रयोग किया जाता है, जब जॉब का एक भाग सिरों के अंत से कुछ दूरी से मिलता है ? A) End-lap input | एंड लैप जोड B) Corner-half lap joint | कोना – अर्ध लैप जोड़ C) Middle-lap joint | मध्य-लैप जोड़ D) Cross-lap joint | क्रॉस-लैप जोड़ 5 / 15 Category: Basic Workshop Practice5) What is the number 1.25 indicates in ISO metric fine thread M12 x 1.252 | आईएसओ मेट्रिक फाइन थ्रेड M12 x 1.25 में 1.25 नंबर क्या इंगित करता है? A) Pitch of the thread | थ्रेड का पिच B) Diametric of the thread | थ्रेड का व्यास C) Depth of the thread | थ्रेड की गहराई D) Length of the thread | थ्रेड की लम्बाई 6 / 15 Category: Basic Workshop Practice6) What is the cause for twisting defect in timber? | लकड़ी में ट्विस्टिंग दोष का क्या कारण है? A) Improper seasoning | गलत सीज़निंग B) Uneven shrinkage | असमान सिकुड़न C) Irregularity in growth of branches | शाखाओं की वृद्धि में अनियमितता D) Defective storage | दोषपूर्ण भण्डारण 7 / 15 Category: Basic Workshop Practice7) Which defect in the timber is caused to reduce its strength? | लकड़ी में कौन सा दोष इसकी शक्ति को कम करता है? A) Twisting | घुमाना B) Cracking | चटकना C) Cupping | कपिंग D) Irregularity | अनियमितता 8 / 15 Category: Basic Workshop Practice8) Which type of notch is used for making a metal tray with 90° bend and an inside flange ? | 90° मोड़ और अंदर से निकले हुए किनारे के साथ धातु ट्रे के लिए किस प्रकार के नॉच का उपयोग किया जाता है? A) Straight notch | सीधा नॉच B) Square notch | वर्गाकार नॉच C) ‘V’ notch | V नॉच D) Slant notch | तिरछा नॉच 9 / 15 Category: Basic Workshop Practice9) What is the use of firmer chisel ? | फर्मर छेनी का क्या उपयोग है? A) Making rectangular holes in wood | लकड़ी में आयताकार छेद बनाना B) Light chiselling and to clean sharp corner | कड़ी में हल्का छेनीकरण तथा तेज़ किनारों की सफाई C) Paring and finishing joints | छीलने और जोड़ों की फिनिशिंग में D) General chiselling work | सामान्य छेनीकरण कार्य 10 / 15 Category: Basic Workshop Practice10) Which type of stake is used for sharp bends in sheet metal? | शीट मेटल में तेज़ मोड़ों हेतु किस प्रकार का स्टेक उपयोग किया जाता है? A) Hatchet stake | हैचेट स्टेक B) Square stake | वर्गाकार स्टेक C) Blow horn stake | ब्लो हॉर्न स्टेक D) Bevel edge square stake | बेवल एज वर्गाकार स्टेक 11 / 15 Category: Basic Workshop Practice11) What is the name of the stake used for general purpose in sheet metal work? | शीट मेटल में सामान्य उपयोग हेतु किस प्रकार का स्टेक उपयोग किया जाता है? A) Blow horn square stake | ब्लो हॉर्न स्टेक B) Hatchet stake | हैचेट स्टेक C) Bevel edge square stake | बेवल एज वर्गाकार स्टेक D) Square stake | वर्गाकार स्टेक 12 / 15 Category: Basic Workshop Practice12) What defect will occur in timber due to irregularity in growth of the branches? लकड़ी में अनियमित रूप से शाखाओं के उगने के कारण कौन सा दोष उत्पन्न होता है? A) Cracking | चटकना B) Knot | गाँठ C) Twisting | घुमाना D) Cupping | कपिंग 13 / 15 Category: Basic Workshop Practice13) What is the purpose of hem folding in sheet metal work? | शीट मेटल कार्य में हेम फोल्डिंग का क्या उद्देश्य है? A) Prevents burrs forming after cutting | काटने के बाद खुरदुरे किनारे बनने से रोकता है B) Prevents the sheet from damage | शीट को क्षति से बचाना C) Helps for forming a square box | वर्गाकार डिब्बे को बनाने में सहायक D) Helps for bending sheet metal easily | शीट मेटल को सरलता से मोड़ने में सहायक 14 / 15 Category: Basic Workshop Practice14) Which file is used for sharpening the blunt teeth of a tenon saw? | एक टेनन आरी के कुंद दांतों को तेज करने के लिए किस रेती का उपयोग किया जाता है? A) Square file | वर्गाकार रेती B) Round file | वृत्ताकार रेती C) Half round file | अर्ध वृत्ताकार रेती D) Triangular file | त्रिभुजाकार रेती 15 / 15 Category: Basic Workshop Practice15) Which type of cold chisel is used for squaring materials at the corners? किस प्रकार की ठंडी छेनी का उपयोग किनारों पर पदार्थों को वर्गाकार करने हेतु किया जाता है? A) Web chisel जाली छेनी B) Half round chisel | अर्ध वृत्ताकार छेनी C) Diamond point chisel हीरा पॉइंट छेनी D) Cross cut chisel | क्रॉस कट छेनी Your score isThe average score is 61% 0% Restart quiz Exit