3 Weldability of SteelWelder Trade / By Er. Roshan Tajne / June 28, 2023 0% Created by Er. Roshan TajneWelder Trade 3 Weldability of Steel 1 / 20 Category: Weldability of Steel1) What should be the bevel angle for edge preparation of 6mm thick pipe welding? | 6 मिमी मोटी पाइप वेल्डिंग की एज को बनाने के लिए बेवल कोण क्या होना चाहिए? A) 40°-45° B) 70°-75° C) 30"-35" D) 60-65° 2 / 20 Category: Weldability of Steel2) How a pipe is specified? | एक पाइप को कैसे निर्दिष्ट किया जाता है? A) Outer dia x inner dia x length | बाहरी डायमीटर x इनर डायमीटर x लंबाई B) Dia only | केवल डायमीटर द्वारा C) Outer dia only | केवल बाहरी डायमीटर द्वारा D) Length only | केवल लंबाई द्वारा 3 / 20 Category: Weldability of Steel3) How many groups of mild steel pipes are there? | माइल्ड स्टील पाइप के कितने समूह होते हैं? A) Five groups | पाँच समूह B) Two groups | दो समूह C) Three groups | तीन समूह D) Four groups | चार समूह 4 / 20 Category: Weldability of Steel4) What is the process of hot weld joint rapidly hammered to relieve internal stresses? | आंतरिक तनाव को दूर करने के लिए गर्म वेल्ड जॉइंट की प्रक्रिया क्या है? A) Annealing | एनीलिंग B) Straightening | सीधा करना C) Peening | पीनिंग D) Heat treatment | उष्मा उपचार 5 / 20 Category: Weldability of Steel5) What is the current range required for 3.15mm dia MS electrode in arc welding ? | चाप वेल्डिंग में 3.15 मिमी व्यास एमएस इलेक्ट्रोड के लिए करंट सीमा क्या है? A) 40-50 A B) 50-60 A C) 70-80 A D) 100-110 A 6 / 20 Category: Weldability of Steel6) What is the purpose of setting root gap ? | रूट गैप स्थापित करने का उद्देश्य क्या है? A) To over some under cut | अंडर कट से बचने के लिए B) Gap get closed due to expansion | विस्तार के कारण गैप बंद हो जाता है C) To control distortion | विकृति को नियंत्रित करने के लिए D) To get good penetration | अच्छी पेनीट्रेशन पाने के लिए 7 / 20 Category: Weldability of Steel7) What is the root run? | रूट रन क्या है? A) The first run is root run | पहला रन ही रूट रन होता है B) Backing run | बैकिंग रन C) The second run is root run | दूसरा रन ही रूट रन होता है D) The third run is root run | तीसरा रन ही रूट रन होता है 8 / 20 Category: Weldability of Steel8) What is the base for selecting the nozzle size for gas welding of a pipe ? | पाइप की गैस वेल्डिंग के लिए नोजल आकार का चयन करने के लिए आधार क्या है? A) Welding position | वेल्ड की स्थिति B) Groove angle | ग्रूव कोण C) Pipe wall thickness | पाइप की दीवार की मोटाई D) Diameter of pipe | पाइप का व्यास 9 / 20 Category: Weldability of Steel9) What is the welding position as per ASME for a pipe joint held vertically, welding in a horizontal line? | एक क्षैतिज रेखा में वेल्डिंग, लंबवत रूप से रखे गए पाइप के लिए ASME के अनुसार वेल्डिंग की स्थिति क्या है? A) 6G B) 2G C) 1G D) 5G 10 / 20 Category: Weldability of Steel10) Which type of stainless steel is weldable ? । किस प्रकार का स्टेनलेस स्टील वेल्ड करने योग्य है? A) Stabilized type | स्थिर प्रकार B) Ferrite type | फेराइट प्रकार C) Nickel type | निकील प्रकार D) Chromium type क्रोमियम प्रकार 11 / 20 Category: Weldability of Steel11) What is the name of last bit of an discarded electrode? एक खारिज इलेक्ट्रोड के अंतिम बिट का नाम क्या है? A) Stubend | स्टब एंड B) Red end रेड एंड C) Waste end | वेस्ट एंड D) Dead end | डेड एंड 12 / 20 Category: Weldability of Steel12) What is the main purpose of ‘Normalising ‘ steel? | नॉर्मलाइजिंग स्टील का मुख्य उद्देश्य क्या है ? A) To make welding operation easier | वेल्डिंग संचालन को आसान करना B) To control hardness | कठोरता को नियंत्रित करना C) To produce fine grain of uniform structure | एक समान संरचना के बारीक ग्रेन का उत्पादन करना D) To prevent cracking | क्रेक को रोकना 13 / 20 Category: Weldability of Steel13) What should be the pre-heating temperature of aluminium job for gas welding? | गैस वेल्डिंग के लिए एल्युमिनियम जॉब का प्री-हीटिंग तापमान क्या होना चाहिए? A) 350°C-400°C B) 300°C-400°C C) 200°C-400°C D) 250°C-400°C 14 / 20 Category: Weldability of Steel14) What is the bevel angle for pipe welding butt joint if wall thickness is more than 5mm ? | यदि पाइप की मोटाई 5 मिमी से अधिक है तो पाइप वेल्डिंग बट जॉइंट के लिए बेवल कोण क्या है? A) 60° B) 80° C) 75° D) 90° 15 / 20 Category: Weldability of Steel15) What is the pre-heating temperature of cast iron ? | कच्चा लोहा का पूर्व- ताप तापमान क्या है? A) 350 to 450°C B) 250 to 350°C C) 300 to 350°C D) 200 to 310°C 16 / 20 Category: Weldability of Steel16) Which type of cast iron possess higher hardness? | किस प्रकार के कास्ट आयरन में उच्च कठोरता होती है? A) Grey cast iron | ग्र कास्ट आयरन B) Nodular cast iron | नोडुलर कास्ट आयरन C) White cast iron | व्हाइट कास्ट आयरन D) Malleable cast iron | मेलीऐबल कास्ट आयरन 17 / 20 Category: Weldability of Steel17) What does the fourth digit indicate as per AWS electrode coding? | AWS इलेक्ट्रोड कोडिंग के अनुसार चौथा अंक क्या दर्शाता है? A) Welding current | वेल्डिंग करंट B) Tensile strength | तन्यता ताकत C) Welding position | वेल्डिंग की स्थिति D) Type of flux coating | फ्लक्स कोटिंग का प्रकार 18 / 20 Category: Weldability of Steel18) Which of the following metals have high thermal conductivity? | निम्नलिखित में से किस धातु में उच्च तापीय चालकता होती है? A) Bronze | कांसा B) Aluminium | एल्युमीनियम C) Brass | पीतल D) Copper | तांबा 19 / 20 Category: Weldability of Steel19) Which filler rod to be used for gas welding aluminium? | गैस वेल्डिंग एल्यूमीनियम के लिए किस फ़िलर रोड का उपयोग किया जाता है? A) Copper Silver alloy | तांबा सिल्वर मिश्र धातु B) Silicon brass | सिलिकॉन पीतल C) Silicon-manganese | सिलिकॉन मैंगनीज D) Pure aluminium, 5% silicon aluminium alloy | शुद्ध एल्यूमीनियम 5% सिलिकॉन एल्यूमीनियम मिश्र धातु 20 / 20 Category: Weldability of Steel20) What flux is to be used for gas welding stainless steel plates ? | गैस वेल्डिंग स्टेनलेस स्टील प्लेटों के लिए किस फ्लक्स का उपयोग किया जाता है? A) Borox flux | बोरोक्स प्रवाह B) Cryolite and berium chloride | क्रायोलाइट और बेरियम क्लोराइड C) Zinc chloride and potassium dichromate paste | जिंक क्लोराइड और पोटेशियम डाइक्रोमेट पेस्ट D) Anti Borox | विरोधी- बोरॉक्स Your score isThe average score is 65% 0% Restart quiz Exit